[ Home Page ]    [ History ]    [ The Project ]

Project Log:  Summary of Phase VI

LABOR 1/11/14 - 10/4/14 281.25 Hours
   
#10 x 1-3/4 screws and 1" fender washers 30
1-1/2" 90° pipe adapter, head discharge 1
1-1/2" ball valve, head discharge 1
1-1/2" black bilge hose, ft 6
1-1/2" black sanitation hose, ft 32
1-1/2" corrugated exhaust hose, ft 6
1-1/2" flange adapter base, head discharge 1
1-1/2" fuel fill hose, ft 3
1-1/2" through hull, head discharge 1
1-1/2" vented loop 1
1" SS Stanchion tops 8
1" vented loop 1
1/16" nylon sheet, black, 12x12 1
1/2" drain hose, shower sump 10
1/2" hose adapters, female NPT 2
1/2" marelon through hull, shower sump 1
1/2" x 38" x 32" bronze acrylic, PH overhead 1
1/4-20 Cheese head 3/4" 20
1/4-20 pan head 3/4 10
1/4-20 X 1 RHMS, SS, pack 25 (deadlights) 1
1/4-20 x 1-1/2 PHMS, SS, pack 10 3
10-24 x 1-1/2" FHMS, nuts, 1" washers 20
120 grit 2" strip, ft 8
120 grit 4" strip, ft 21
14 x 1-1/4 SS FHSMS, box 2
14/2 cable, mast 40
14/3 bilge pump cable 12
220 grit 2" strip, ft 8
220 grit 4" strip, ft 10
2AWG battery cable red 30
2AWG battery cable yellow 10
2AWG battery lugs 12
3/4" 90° pipe adapter, head intake 1
3/4" ball valve, head intake 1
3/4" exhaust hose, ft 8
3/4" flange adapter base, head intake 1
3/4" through hull, head intake 1
320 grit 2" strip 28
4-gang terminal block 4
4/4 cherry BF 9.5
40 grit 5" disc, ea 16
4200, tube 1
4AWG cable, red and yellow (Treatment System) 40
5/8" bolts and nuts for tabernacle pins 1
5/8" vent hose, ft 12
6 x 1 FHSMS, Box 100 1
6" biax, ft 22
6" locking deck plate 2
6" screw-in deck plate 1
60 amp circuit breaker 1
80 grit 2" strip, ft 3
80 grit 4" strip, ft 34
80 grit 5" disc, ea 6
Acorn nuts, 3/8 1
Antifreeze, gallon 1
Aquasignal series 40 side lights and stern light 3
AWAB 13-20 2
AWAB 15-24 6
AWAB 19-28 11
AWAB 32-44 4
AWAB 38-50 18
Battery Switch Dual Circuit Plus 5511E 1
Bomar Access hatch, head 1
Brass handle, head door 1
Butyl tape, roll 1
Captain's varnish, qt 2
Chainplate fasteners 8
Coax cable, mast 40
Door hook 3
Engine oil 15W-40, Rotella 1
Epoxy resin, mixed, oz. 132
Exhaust wrap 1
Eye straps, lazy jacks (4) 2
Fixed block Wichard 2
Fixed block with becket Wichard 1
Formica sheet, white 3
Fuse holder 2
GPS antenna mounts 2
Harken carbo 20mm cheek block 2
HD shrink tubing, battery cables, 48" length 1
Holding tank vent 5/8" Moeller 1
Honduras mahogany 42 x 12 x 1, BF 3.5
Life Calk Teak 1
Lift handle, engine room 6
Metz VHF Antenna 2
NAPA 8144 6-volt 2
NAPA 8303 Start Battery 1
New lifelines 1
Non-mortise hinges 3
Overhead light, head 1
Plastic junction box, mast wiring 1
Plug for heat exhaust 1
Plug for heat intake` 1
Push button switch, refer fan 1
PVC pipe and fittings for ladder template 1
Red and green paint, pints each 2
Roller Pan--contact cement 1
Scanstrut deck seal .83 1
Shakespeare PL259 connector 2
Shields 250 1" hose 10
Shower rail, valve, hand shower 1
Sikaflex 209 Primer 1
Sikaflex 291-LOT 3
Sikaflex 295UV for overhead acrylic hatch 2
Six10 mixing tip 3
Six10 Tube 1
SS Draw latch, corner 8
Terminal block, 6 gang 1
Terminal fuse block dual 1
Terminal fuse block single 2
Terminal fuses 150A 4
2" Sound insulation, roll 1
West System foam roller 2
Whale bilge pump 1212 1
Windex 15 1

< Previous | Next >


The Motorsailer Project
Site design and content ©2010-2015 by Timothy C. Lackey.  All rights reserved.

Please notify me of broken or missing links or other site issues.
You can always find every day's project log links on The Project page.

Questions and comments | Home Page
V1.0 went live on 8/26/10